• Cannon CANTERBURY INBUILT MODELS USER INSTRUCTIONS INSTALLATION INSTRUCTIONS This heater is approved for use with Natural and Propane gases. SERVICE INSTRUCTIONS Please leave instructions with the owner. • Contents Contents Warranty ❍ Distributor Safety warnings ❍ What to do if you smell gas ❍ Warnings ❍ Standards User instructions ❍ Operating instructions ❍ Cleaning ❍ Flame characteristics Heater specifications Installation instructions 10-15 ❍ Clearances ❍ Installation into a masonry/brick or mock fireplace ❍.

• Warranty The Cannon appliance is warranted against defects in materials and work- manship for a period of one, (1) year from its date of original purchase, for residential use in Australia. Warranty service, which includes parts and labour for the replacement or repair of defective parts, is available through the CANNON distributor. • Refer to other sections of this manual for correct procedures, or consult with place of purchase, a licensed plumber, a gas supplier or the CANNON distributor listed in this manual. Do not build the heater into bookcases or walls. Install only in loca- tions as referred to in these installation instructions. • Before testing the flue confirm air vents are unobstructed.

If an exhaust fan or other heating appliances are present switch them on. This is to test that there is no interaction between the Cannon heater and other appliances. Refer AS5601. • User instructions Operating instructions 1. Plug the power cord into the wall socket and turn on the power to the heater, see figure 1.

Refrain from using an extension cord. For control lay-out refer to figure 2 3.

To turn heater on press switch to POWER ON position. There is a 5 second delay before the burner ignites. To increase the fan speed to MED, press switch for MED setting. Refer figure 5.

View & download of more than 471 Cannon PDF user manuals, service manuals, operating guides. Drivers License Test Questions Bahamas Cruise. Cookers, Kitchen appliances user manuals, operating guides & specifications.

To increase the fan speed to HIGH, press switch for HIGH setting. Refer figure 6. To turn the burner to LOW setting, press switch for LOW setting.

Refer figure 7. • Cleaning All cleaning should be carried out when the heater is cold. Normally the heater should only need wiping with a lint - free damp cloth. Any stubborn stains can be removed with a non-abrasive spray on cleaner. If an abrasive cleaner is used the paint finish will be damaged. • Heater specifications Gas type: Natural or Propane gas, as indicated Note: on data label The data plate is located on Gas consumption: 26 MJ/hr input the fan chamber base, rear of the lower fascia. Energy output: 21.45 MJ/hr (5.96 kW) Energy star rating: 4 stars Heater type.

• If installing into a mock fireplace a mock fireplace installation kit MUST be used. Anime Kimi Ni Todoke Season 2 Sub Indo more. The mock fireplace instal- lation kit can be ordered from the CANNON distributor.

Order speci- fication for the part is ‘MOCKKITRO’. • Refer AS5601.

For “air movement not to affect appliance” see clause 5.3.1. For ‘air supply to appliance’ see clause 5.4.1.

For ‘ventilation requirements’ see clause.5.4.3. Installation WITH a flue connected. • Installation WITHOUT a flue connection. Prepare electrical and gas connections. Remove the lower front cover, see figure 16.

A 10 Amp wall socket needs to be located within 1.5m of the heater. If using a power point in the chimney, route the plug and cord through cord access at lower LH side of rear panel.

Remove the inner glass. Slacken off screws in top clamp and remove side clamps. Refer figure 20. All gaps between heater case and fireplace are to be sealed. Seal with foam tape around top and sides of heater flange as required. • Gas connection 13.

Slide heater into the fireplace ensuring that gas inlet pipe is fed through the hole at the rear bottom RHS of the heater. Refer figure 22 and gas connection figure 24. 14.With heater in position, flanges should be hard against masonry. Se- cure case flanges to masonry. • Log installation 16.

The burner is contained within the burner chamber. Refer figure 25. Sniper Elite V2 Password Rar File here. Carefully unpack the log set. Logs are numbered as follows: No 1 - Left front log No 2 - Left back log No 3 - Right front log No 4 - Right back log Position the four individually numbered logs in the following order on the burner head as shown in figure 26-29.